Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor

Description

Home
Arduino
Module
Sensor
Chips
About Us
Description:
Dissipation Power:1.9 Inches & Under
Condition:New
Supply Voltage:DC6.0-30V
Model Number:XY-T01
Operating Temperature:-40-+85
℃
NTC10K sensor
Functions:
Set Temperature ---- SetT;
Backlash Temperature-----BackT;
1. Heating Mode 'H':
When Temperature ≤ SetT - BackT Relay conduction, heating equipment begin to work;
When Temperature ≥ SetT, Relay disconnect, heating equipment stop work;
2. Refrigeration mode 'C':
When Temperature ≥ SetT + BackT Relay conduction, refrigeration equipment begin to work;
When Temperature ≤ SetT Relay conduction, refrigeration equipment stop work;
3. High Temperature Alarm 'ALA':
When Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;
4. Delay Start ‘OPH':
When a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;
5. Temperature Correction Function OFE(-10.0 ~ 10.0°):
The system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;
6. Parameter Remote Read/Set:
The parameters such as setting temperature, backlash temperature and temperature correction can be set through UART.
7. Real-time Temperature Report:
If the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;
8. Relay enable (default enable):
If the relay is disable, the relay remains disconnected;
9. Restore factory Settings:
At the same time press the STOP, set key more than 3S, restore factory settings;
Working mode setting /backlash temperature :
1. In the running interface, short press SET key, enter the Quick setting interface;
2. After entering the Quick Setup interface, switch the parameters
3. Through the UP DOWN key, modify the parameter value, support short press/long press;
4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;
Alarm temperature/delay Start /temperature correction:
1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;
2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;
3. through the UP DOWN key, modify the parameter value, support short press/long press;
4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters
How to turn on high temperature alarm (default off):
Enter the parameter setting interface, switch to the alarm parameter ALA , turn on or off the high temperature alarm function by short pressing the STOP button, and if the high temperature alarm function closes, ALA displays \'----\' as a reminder;
How to turn on delay start (default off):
Enter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature
Serial Control (MCU UART)
Communication standards:9600bps Data bits :8
Stop Bits :1
CRC :none
Flow control :none
CMD
Description
start
Start temperature report
stop
Stop temperature report
read
Read parameters setting
on
Relay Enable
off
Relay Disable
S:XXX
Setting Temperature
-50 ~ -01
00.0~99.9
100~110
B:XX.X
Set Backlash Temperature (00.0~30.0)
OFE:XX.X
Temperature Calibration(-10.0 ~ 10.0)
ALA:XX.X
Alarm Temperature(-50.0 ~ 110.0)
OPH:XXXX
Delay Start(0 ~ 9999 Minutes)
Note:
Measuring temperature range: -50℃ to 110℃
Package Included:
1 x XY-T01 Digital Thermostat
Instructions not included - please see product description
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
Fill your shipping info
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.